Idaho Collection
[Hand Scraped | Engineered | 3/8”]
LIMITED WARRANTY
Finish: 25 year
Structural: Lifetime
SERIES INFORMATION:
#382 HS-E-#386 HS-E
Species/Janka| Hickory (1780) |
|
Thickness| 3/8” |
|
Width| 6” |
|
Length| 1’-6’ |
|
Wear Layer| 1.5MM |
|
SF/BOX| 29.53 |
|
BX/PLT| 41 |
|
SF/PLT| 1063 |
|
BX/WGT| 41 |
|
SF/WGT| 1.39 lbs. |
|
Waste %| 5-7% |
|
#387 HS-E-#391 HS-E
Species/Janka| Birch (1260) |
|
Thickness| 3/8” |
|
Width| 5” |
|
Length| 1’-4’ |
|
Wear Layer| 1.5MM |
|
SF/BOX| 36.09 |
|
BX/PLT| 50 |
|
SF/PLT| 1299 |
|
BX/WGT| 50 |
|
SF/WGT| 1.39 lbs. |
|
Waste %| 5-7% |
|
#482 HS-E-#483 HS-E
Species/Janka| Acacia (1750) |
|
Thickness| 3/8” |
|
Width| 5” |
|
Length| 1’-4’ |
|
Wear Layer| 1.5MM |
|
SF/BOX| 36.07 |
|
BX/PLT| 50 |
|
SF/PLT| 1299 |
|
BX/WGT| 50 |
|
SF/WGT| 1.39 lbs. |
|
Waste %| 5-7% |
|
INSTALLATION:
ADDITIONAL INFORMATION:
Core Construction| 6 Ply - Hardwood |
|
Joint System| Tongue and Groove |
|
Texture| Hand Scraped (Hand Crafted)/Brushed |
|
Edge Profile| Hand Sculpted, Chattered, |
Pillowed Edge |
Texture| Smooth |
|
Finish Type| 9 Finish Coats - UV cured urethane infused with aluminum oxide |
|
Gloss Levels| 13%-16% |
|
Maintenance| Bona Hardwood Formula |
|
Repair Finish| Can be screened and recoated with Bona HD Traffic (or similar) |
|
Expansion Requirements| Requires 1/2” expansion gap. Floating installations require T-molds for |
installations exceeding 40 lineal feet in length or width and 30 lineal feet for installations over in floor radiant heat. |
| Fastener Requirements 18 gauge, L/T cleats or 1/4” crown staples, minimum 1-1/2” long. Fasteners spacing 1-1/2” from the board ends and every 3”- 4” along the tongue |
|
Uses| (Hickory & Acacia) |
Residential, Light Duty Commercial (Birch) Residential |
COMPLIANCE:
COMMON QUESTIONS:
SUBSTRATE REQUIREMENTS
Structurally sound, well bounded, flat to within 3/16” in 10’ radius, or 1/8” in 6’ radius. Vertical deflection cannot exceed 1/4” in 10’ radius, or more than 1/16” between the floor joist.
APPROVED SUBSTRATES
Underlayment APA grade CDX plywood/OSB, 3000 PSI concrete or 2500 PSI gypcrete. Underlayment grade MDF (floating only).
WOOD SUBFLOOR (EMC) MOISTURE CONTENT REQUIREMENTS
Engineered wood MC (moisture content) must test within 3% of the wood subfloor. Neither can exceed 12%. If the MC falls outside this range, a longer acclimation period is required to reach equilibrium.
CONCRETE AND GYPCRETE MOISTURE EMISSIONS, RH, AND PH REQUIREMENTS
Installing a vapor barrier is not required, but it is strongly
recommended on installations over on or above grade slabs with a calcium chloride reading under 3 lbs /1000sf per 24 hours or under 75% relative humidity as determined by current ASTM standards, or a CM (calcium carbide) rating of 2.5% or less. The pH levels must be between 5 – 9. Below grade and any substrate over 3 lbs /1000sf per 24 hours require a vapor barrier.
JOBSITE CONDITION RANGES
Prior, during, and after installation, the jobsite RH must be maintained between 35-55%, and the room temperature between 60-80°F.
ACCLIMATION TIMEFRAME
Minimum 24 hours to reach room temperature between
60-80°F and 48 hours if the material was stored or transported in temperature below 60°F within 24 hours of install.
CAN WE INSTALL A CUSHION UNDERNEATH THE FLOOR?
YES, FOR FLOATING INSTALLATION ONLY. Approved cushions are high density #59EVA 3mm, #59IXPE 3mm, #60PVC 1.5mm, and cork up to 1/4” in thickness. EPE economical cushion is not recommended.
RUG COMPATIBILITY
Must be breathable, non abrasive, natural fiber rugs. Please see RugPadUSA.com. For example; Eco Plush 3/8”, Contour Lock, RugPro, or Superior Lock 1/4”.RugPro, or Superior Lock 1/4”.
